You have 0 items in your cart.
Products
Sub Categories
| Name | SKU | Description | Category | ||
|---|---|---|---|---|---|
|
GW INSTEK AFG-3000 Series | Features * Wide frequency range from 1uHz to 80/50MHz* High 200MSa/s sampling rate * 16-bit Amplitude Resolution* Output from any section of 1M-point-long waveforms* 4.3" high resolution LCD display/on-screen help/Impedance switch* Four ways to generate arbitrary waveforms: Front Panel Operation CSV file uploading, Direct Waveform Reconstruction (DWR), ArbitraryWaveform Editing PC Software * USB, RS-232, GPIB interface support | Arbitrary Function Generators |
|
|
|
GW INSTEK SFG-1000 Series | Features *DDS Technique and FPGA Chip Design *Frequency Range:0.1Hz~3MHz *High Frequency Accuracy : ± 20ppm *High Frequency Stability : ± 20ppm *Max. Frequency Resolution : 100mHz *Low Distortion Sine Wave : -55dBc,0.1Hz~200kHz *Voltage Display (Only SFG-1013) | DDS Function Generators |
|
|
|
GW INSTEK SFG-2100/2000 Series | Features *DDS Technique and FPGA Chip Design *Frequency Range : 0.1Hz~4/10MHz *High Frequency Accuracy : ± 20ppm *Frequency Resolution : 100mHz *Low Distortion Sine Wave : -55dBc,0.1Hz~200kHz *Front Panel Setting Save/Recall with 10 Groups of Setting Memories *Built-In 9 Digits,150MHz/High Resolution Counter(SFG-2110 Only)*INT/EXT AM/FM Modulation (SFG-2110 Only)*LIN/LOG Sweep Mode(SFG-2110 Only) | DDS Function Generators |
|
|
|
GW INSTEK GFG-8015G | Features *Frequency Range : 0.2Hz ~ 2MHz *Waveform : Sine, Triangle, Square, TTL Pulse *Variable DC Offset Control *Output Overload Protection *VCF Input Function *1000 : 1 Tuning Range | Analog Function Generators |
|
|
| GW INSTEK GFG-8020H | Features *Frequency Range : 0.2Hz ~ 2MHz *Coarse and Fine Tuning *Waveform : Sine, Triangle, Square, TTL Pulse *CMOS Output *Built-In 4 Digits Counter (INT Only) *Large 0.5" LED Display *Variable DC Offset Control *Output Overload Protection *VCF Input Function | Analog Function Generators |
|
||
|
GW INSTEK GFG-8200A Series | Features *Frequency Range: 0.3Hz ~ 3MHz (GFG-8215A/8216A/8217A/8219A)*Frequency Range: 0.5Hz ~ 5MHz (GFG-8250A/8255A)*Waveforms: Sine, Triangle, Square,Ramp, TTL and CMOS Output*External Voltage Controlled Frequency (VCF) Function *Two-Steps (-20dBx2) and Variable Attenuator *Built-In 6 Digits Counter with INT/EXT Function up to 150MHz(Except GFG-8215A)*INT/EXT AM/FM Modulation (GFG-8219A/8255A)*GCV Output for Synchronization (GFG-8219A/8255A) | Analog Function Generators |
|
|
|
GW INSTEK GFG-3015 | Features *Frequency Range 0.01Hz~15MHz *Maximum Frequency Resolution 10mHz *Dual Displays Indicate Frequency and Amplitude *Built-in 6 Digits Counter up to 150MHz/High Resolution *Output Waveforms Sine,Square,Triangle,Ramp,Pulse,Sweep,Gate or Burst *INT/EXT AM/FM Modulation *GCV Output for Synchronization *Output Overload Protection | Analog Function Generators |
|
|
|
GW INSTEK GAG-810/809 | Features *Frequency from 10Hz ~ 1MHz *0.02% Low Sine Wave Distortion (GAG-810 Only)*6 Steps Output Attenuator *EXT SYNC Function | Other Signal Sources |
|
|
|
GW INSTEK GSG-120 | Features *Freq Range 100kHz ~ 110MHz *Output Level -19 ~+99 dBu *All Operations are Controlled by Microprocessor *Memory Storage: 10 points in one block(up to 100 continuous points) *and 4 output levels *Memory Data Copy *Back Space key *Remote Control Function(Need the GRC-1201 option) *FM Stereo Modulation (GSG-122 only) | Other Signal Sources |
|
|
|
GAS DNA GMS 2000 Multi-channel digital controller for gas detector | GMS-2000 is multi-channel digital controller to monitor gas leakages from more than one gas detectors simultaneously. GMS-2000 is composed of one alarming unit & more than one receiving units. While each receiving units in GMS-2000 receive density signals from external gas detectors, when the density becomes higher than alarm value, receiving units automatically give signal to alarming unit to sound alarm. GMS-2000 transmits the relay output and standard current output signal 4-20㎃ to... | Digital Controller |
|
|
|
GAS DNA GMS1500 4-Channel digital controller for gas detector | GMS-1500 is four channel digital controller which can be connected to four (4) gas detectors. Receiving analogue continuous signal from four (4) detectors and converting it into digital signal, GMS-1500 provides various alarming and monitoring environment by micro-processor. Also, GMS-1500 converts digital signal into the 4-20㎃ standard current signal for output signal which can be transmitted to various external devices such as PLC, DDC, RECODER, and so on. Using these functions, you can... | Digital Controller |
|
|
|
GAS DNA GMS1000 Single -Channel digital controller for gas detector | GMS-1000 is one point digital controller which can be connected to only one(1) gas detector. Receiving analogue continuous signal from one (1) detector and converting it into digital signal, GMS-1000 provides various alarming and monitoring environment by micro-processor. Also, GMS-1000 converts digital signal into the 4-20㎃ standard current signal for output signal which can be transmitted to various external devices such as PLC, DDC, RECODER, and so on. Using these functions, you can easily... | Digital Controller |
|
|
|
Center CENTER 26 - Flexible Current Meter | The new flexible current probes make your measurement possible where the space is too tight or difficult for clamp meters. Center 26 is composed of a 8.5mm, double-insulated flexible sensor and a True-RMS electronic module with back-lit LCD for accurate and clear reading in all environments. Measurement range from 1 to 3000 A ac, available in 10" and 18" length probe. | Flexible_Clamp |
|
|
|
Center CENTER 25 - Flexible Current Probe | Plug into multimeters, oscilloscopes, or power analyzers to measure AC current, up to 3000 A ac. Center 25 is also ideal for commercial or residential users who have standard clamp meters, but need to reach hard-to-clamp-on places, or occasionally measure AC current higher than 400 or 600 A. Center 25 simply eases your work. | Flexible_Clamp |
|
|
|
Center CENTER 260 - mA High Resolution Clamp Meter (AC/DC, TRMS) | The CENTER 260 is the perfect instrument for diagnostics and maintenance in areas with low current measurement requirements. It measures both AC and DC current with a very stable 1 mA resolution. It is the ideal choice not only in general industrial applications, but also in utility, automotive, aviation and marine applications to measure standby or leakage currents in the mA range right up to 100A, AC or DC. The backlit LCD and bright LED flashlight make it easier to work in dimly lit... | Clamp_Meters |
|
|
|
Center CENTER 252 - Small-size Clamp Meter (AC/DC, TRMS) | The CENTER 252 is a True-RMS clamp meter capable to measure AC and DC current/voltage, with 0.01A/0.1V high resolution. It also comes with 1ms Peak Hold function for fast capture of signals, and Zero function to easily analyze data. No matter in self-employed, industrial maintenance, or professional applications, the CENTER 252 brings a reliable, accurate, and convenient solution. | Clamp_Meters |
|
|
|
Center CENTER 251 - Small-size Clamp Meter (HVAC, TRMS) | In this Hvac filed, the electricians need more than what ordinary clamp meters can do. Equipped with DCμA function for flame rectification or heating sensor test. Capacitance and temperature functions are also designed for fitting the needs in the Hvac applications. 1ms Peak Hold function for fast capture of signals. CENTER 251 is also a True-RMS clamp meter and its safety rated 600V CAT III. | Clamp_Meters |
|
|
|
Center CENTER 250 - Small-size Clamp Meter (AC, TRMS) | When you need to analyze the INRUSH current of electric motors or other devices, CENTER 250 delivers the solution. With 0.01A high resolution to measure up to 660A AC current, the CENTER 250 is ideal tool for general purpose applications. Built-in backlit LCD, True-RMS, rated 600V CAT III, it’s not only easy, convenient, but also safe to use. | Clamp_Meters |
|
|
|
Center CENTER 235 - Leakage Clamp Meter (AC) | The leakage clamp meter CENTER 235 has a very good resolution of 10μA. It is very useful for power system check and installation. With the measurement range up to 100A, it is also proper for indoor installation as a normal clamp meter. | Clamp_Meters |
|
|
|
Center CENTER 232 - Watt Clamp Meter (AC/DC, TRMS) | The CENTER 232 is used in power system maintenance. Besides power measurement, it also provides the voltage, current measurement, and continuity functions. | Clamp_Meters |
|